Insights

How Much Syngas Is Produced in Gasification? Nm3/kg

Zero-X·2026-11-02
How Much Syngas Is Produced in Gasification? Nm3/kg

How much syngas is produced in gasification? For an air-blown downdraft gasifier on wood, the measured answer is about 2 to 2.5 normal cubic metres (Nm3) of gas per kg of fuel. A 10 kg/h pilot plant run by IndianOil on wood chips and briquettes reported 1.9 to 2.2 Nm3/kg, and a small wood-fired power plant in Brazil measured 2.5 Nm3/kg.

Across feedstocks and agents, published yields span roughly 1.2 to 3 Nm3/kg. That spread is not noise. It mostly tells you what was blown into the reactor, and that is why the volume number on its own is the wrong figure to buy a plant on. This guide gives the yields, explains what inflates them, and shows the questions we ask instead when we size a unit.

Syngas yield by feedstock and gasifying agent

The table collects measured and modelled yields from open literature. Every row is a different reactor, so read it as a range finder, not a league table.

FeedstockAgent / reactorGas yield, Nm3/kgNote
Wood chips, briquettesAir, downdraft, 10 kg/h1.9 to 2.2ER 0.28 to 0.34
Wood wasteAir, downdraft plus engine2.55.6 kg/h fuel
Lignite and sawdust briquetteAir, downdraft, 10 kWe2.99at ER 0.386
Waste woodAir, downdraft2.1ER 0.23
Waste wood plus 12.5% sludgeAir, downdraft2.9ER 0.35
Switchgrass plus 0 to 40% MSWAir, commercial downdraft1.6 to 1.4falls as MSW rises
Switchgrass plus MSW (model)Air and steam1.16 to 1.39dry gas, simulation
Torrefied sawdustOxygen, fluidized bed2.529.31 MJ/Nm3
Mixed plastic wasteOxygen and steamabout 2.01,998 Nm3 per tonne

Wood and woody biomass

Clean wood is the reference case, and the numbers cluster tightly around 2 Nm3/kg. The highest figure in this group, 2.99 Nm3/kg at an equivalence ratio of 0.386, came with a cold gas efficiency of 80.03% and a heating value of 4.91 MJ/Nm3. More air bought more gas, but each cubic metre was thin.

Sewage sludge blends

Sludge is where yields get interesting and plants get into trouble. In a downdraft test on waste wood and sewage sludge blends, pure wood gave 2.1 m3/kg, a 12.5% sludge blend gave 2.9 and a 25% blend gave 3.0, while tar fell from 24.1 to 3.7 g/kg. The catch: sludge ash formed agglomerations, and the authors advise against more than 12.5% sludge in a downdraft. They also note their air flow correlation may have overstated efficiency. A separate study gasified 20 wt% dried sludge with wood successfully at 4.5 MJ/Nm3, but at 33 wt% the gasifier blocked with agglomerated ash. Our full take on this feedstock is in sewage sludge gasification.

Municipal solid waste

MSW tends to lower the yield. A review of waste gasification for hydrogen reports that co-gasifying switchgrass with MSW in a commercial downdraft unit gave 1.6 Nm3/kg falling to 1.4 Nm3/kg as the MSW share rose from 0 to 40 wt%. An Aspen Plus model of the same pairing found dry gas yield dropping from 1.22 to 1.16 Nm3/kg, with a best case of 1.39 Nm3/kg at a cold gas efficiency of only 39.92%. Ash, moisture and inert content all take volume away.

Plastics

Plastics carry a lot of hydrogen and very little ash. A life cycle inventory for a mixed plastic plant lists 1,998 Nm3 of syngas per tonne of plastic waste. Read the inputs too: that tonne becomes 850 kg of granulate after shredding and is gasified with 731 Nm3 of oxygen and 1,096.5 kg of steam. Part of the gas volume comes from what you feed alongside the waste. We cover the feedstock in depth in plastic waste gasification.

Why air-blown gasifiers report the most gas

Air is about four fifths nitrogen, and nitrogen passes straight through the reactor into the gas. In a commercial air-blown wood gasifier, dry producer gas measured 43 to 48% nitrogen, roughly half the volume. We break the gas down component by component in our guide to syngas composition. So a large Nm3/kg figure from an air gasifier partly measures how much air went in.

The heating value shows the trade. The same review puts gas from air at 4 to 7 MJ/Nm3, from pure oxygen at 10 to 12 and from steam at 15 to 20. In a direct comparison on sawdust, oxygen produced the highest yield, 2.52 Nm3/kg, at 9.31 MJ/Nm3, well above the 4 to 7 MJ/Nm3 of air-blown gas. Fewer, richer cubic metres are easier to clean, compress and convert. For the agent choice itself, Energaia's comparison of air, oxygen, steam and CO2 as gasifying agents goes through each option. We explain why we chose the nitrogen-free route in oxy-steam gasification.

Ask for energy or hydrogen per kg instead

If the gas goes to an engine, the number that matters is energy per kg: yield times heating value, or cold gas efficiency. If the gas goes to hydrogen, the number that matters is grams of hydrogen per kg.

Hydrogen per kg has a hard ceiling. Biomass holds 6 to 7 wt% hydrogen, which the KIT review equates to 0.67 to 0.90 Nm3 of hydrogen gas per kg. Steam can add more through the water-gas shift, which is the whole case for it. In oxy-steam experiments at the Indian Institute of Science, a downdraft reactor reached 104 g of hydrogen per kg of dry wood at 50.5% hydrogen in the gas, against about 40 g/kg and 20% with air. The best energy efficiency, 80.3%, came at a lower steam ratio with 66 g/kg. You trade energy for hydrogen, and you choose where to sit.

What moves the yield

Equivalence ratio

The equivalence ratio (ER) is the air or oxygen fed, divided by what full combustion would need. Raising ER adds oxidant and gas volume, which is visible in every downdraft row above. Past a point it burns product gas instead of making it, and heating value falls.

Temperature and steam

Hotter beds convert more char to gas. A dual fluidized bed model found that temperature has a stronger effect on gas yield than the steam to biomass ratio; more steam mainly raises the H2/CO ratio rather than the volume.

Ash and moisture

Ash is dead weight that leaves as residue, not gas. A 2024 review found lower ash correlated with higher syngas yield, contrasting sewage sludge at 30.8 wt% ash with medical waste at 1.47 wt%. Report yields per kg of dry, ash-free fuel if you want to compare feedstocks fairly.

A sizing rule of thumb

For first-pass sizing, multiply feed rate by the literature range for your feedstock and agent. As illustrative arithmetic, not a performance guarantee: a unit fed 100 kg/h of dry wood at 2 Nm3/kg makes on the order of 200 Nm3/h of air-blown producer gas. The same unit on high-ash sludge or MSW should be sized lower, and an oxygen or oxy-steam unit makes fewer cubic metres of richer gas. Then convert to what you sell. The plastics inventory above converts its gas through combined heat and power to 1,850 kWh per tonne of plastic waste, which is a more useful number for a business plan than the cubic metres.

Reactor type changes all of this. Fixed bed, fluidized bed and entrained flow units sit in different parts of the table, as our overview of types of gasifiers explains.

What we measure on the X-150

Our X-150 is a containerized fixed-bed downdraft gasifier in the 150 kg/h class, and we run it in oxy-steam mode on real waste. In an 80 day, 1,939 hour continuous campaign in Paris within the COMETHA project, it processed 16,382 kg of digestate pellets and produced syngas with:

  • 33% hydrogen
  • an H2/CO ratio of 1.95:1
  • zero nitrogen ballast
  • 99.98% tar conversion

We have not published a gas volume per kg from that campaign, so we will not quote one here. What we do publish is the part that matters for hydrogen and synthesis: no nitrogen to strip out, a ratio sitting at the 2:1 synthesis window, and a tar level that the cleaning train can handle. On waste feedstocks like digestate, that combination is rarer than a big cubic metre figure. The heating value side of the story follows in our upcoming guide to syngas heating value.

FAQ

How many cubic metres of syngas does 1 kg of wood make?

About 1.9 to 2.5 Nm3 in air-blown downdraft gasifiers, measured on wood chips, briquettes and wood waste. Roughly half of that volume is nitrogen from the air.

How much syngas does a tonne of plastic waste produce?

One published inventory gives 1,998 Nm3 per tonne of mixed plastic waste, using oxygen and steam as agents. The oxygen and steam fed in contribute part of that volume.

Does a higher gas yield mean a better gasifier?

Not on its own. Air inflates the volume with nitrogen and lowers heating value. Compare cold gas efficiency, energy per kg or hydrogen per kg instead.

How much hydrogen can gasification make per kg of biomass?

The hydrogen in biomass alone corresponds to about 0.67 to 0.90 Nm3 per kg. Steam adds more: oxy-steam tests reached 104 g of hydrogen per kg of dry wood, against about 40 g with air.

We use cookies to improve your experience on this site. By continuing, you agree to our Privacy Notice.